-
Peter-swe reageerde in het onderwerp Mixing crankcase halves in het forum General questions 2 jaar, 9 maanden geleden
Lath copper-copper mesh? Where does one source such thing? Or are you saying liquid gasket and paper might do? What is an acceptable sealant? Hylomar based something? Every forum seem to favor something different…
-
Peter-swe reageerde in het onderwerp Mixing crankcase halves in het forum General questions 2 jaar, 9 maanden geleden
Crankshaft moves good when rotating in the crankcase only (two new bearings and a lubricated seal resisting)
Force required to get the cylinder skirt in. This is when the cylinder does not move properly when it hits the pots-definitely more resistance-makes absolute sense, what you are saying. I should spilt the case, shaft out and open up the…[Lees meer] -
Peter-swe heeft het onderwerp Mixing crankcase halves aangemaakt in het forum General questions 2 jaar, 9 maanden geleden
One Cdi crankcase with open small half due to oil pump (ciao mix)
One pionts crankcase with normal, closed small half.
One gets mazzucchelli 10mm pin crankshaft.
Reusing the 10mm pin crankshaft with a longer end that drives the oil pump. This one needs the open half to fit.
Can I swap/exchange the two small halves?
I want to use the mazzucchelli…[Lees meer] -
Peter-swe reageerde in het onderwerp Request for a favor –some hand-holding 🙂 in het forum General questions 2 jaar, 11 maanden geleden
DR43mm seems to be out of stock everywhere! 🙂 Must be really good
Thanks for chiming in and confirming 13/13 is a solid choice. From the looks of it, I will need few carburetors…and DR43mm kits when they become available. The question now is how to proceed with the motors–the 12mm pin one is a risk considering the poor…[Lees meer]
-
Peter-swe reageerde in het onderwerp Request for a favor –some hand-holding 🙂 in het forum General questions 2 jaar, 11 maanden geleden
sx3-swe wrote:
Hi Peter, I guess you’ve imported thoose mix-ciaos to Sweden? Since they weren’t sold on our market. No license plate required as you state, but you still need the “typintyg” for the mopeds to be road legal. Not saying that I following that very strictly at all, but tecnically it’s in the books. 🙂 Thoose who attended VCNL meet 201… -
Peter-swe reageerde in het onderwerp Request for a favor –some hand-holding 🙂 in het forum General questions 2 jaar, 11 maanden geleden
Thank you for the warm welcome and Zevenenergie, what a wonderful creature that is 😛 !
Here is the situation as of now:
Black Ciao:- Looks like a Mix, motor is from a Mix, frame carries C2400 plate, oil pump missing and tank isolated.
- No variator
- Electronic ignition
- Scored piston, a LOT less scoring on cylinder but visible, not…
-
Peter-swe wijzigde zijn profielfoto 2 jaar, 11 maanden geleden
-
Peter-swe heeft het onderwerp Request for a favor –some hand-holding 🙂 aangemaakt in het forum General questions 2 jaar, 12 maanden geleden
Hello fellow moped aficionados!
I have been reading around the forum a bit but I think I still need some hand-holding in my first steps into this awesome madness.
I am a happy owner of 3 different Ciaos in various stage of disarray! Two are MIX based, one is a PX, all are circa 1999. All are 25km/h, only one runs as it should. One is in discrete…[Lees meer] -
Peter-swe is geregistreerd lid geworden 2 jaar, 12 maanden geleden